Mettler Toledo M400 Spezifikationen Seite 39
- Seite / 88
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Transmitter Multiparameter M400 39
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
8 Configuration
(PATH: Menu / Configure)
Configure
Measurement Analog Outputs Set Points Alarm/Clean ISM Setup* Display Hold Outputs
* Only available in combination with ISM sensors
8.1 Enter Configuration Mode
While in Measurement mode, press the key. Press the or key to navigate to the
Configure – Menu and press [ENTER].
8.2 Measurement
(PATH: Menu / Configure / Measurement)
Enter configuration mode as described in Section 8.1.
Press the [ENTER] key to select this Menu. The following sub menus can now be selected:
Channel Setup, Temperature Source, Comp / pH / O
2
and Set Averaging.
8.2.1 Channel Setup
(PATH: Menu / Configure / Measurement / Channel Setup / Select Channel ISM)
Press the [ENTER] key to select the ”Channel Setup” Menu.
Conventional (analog) Sensor
Select Sensor Type (Analog or ISM) and press [ENTER].
Available Measurement Types are (depends on transmitter type)
Measurement parameter Type
pH / ORP = pH or ORP 1,2,3
Cond (2) = 2 electrode conductivity 1,2,3
Cond (4) = 4 electrode conductivity 1,2,3
O
2
hi = only Dissolved oxygen (ppm) (no gas) 2,3
O
2
lo = only Dissolved oxygen (ppb) (no gas) 3
The 4 lines of the display can now be configured with sensor channel ”A” (if analog Sensor is
chosen) or ”B” (if ISM Sensor is chosen) for each line of the display as well as measurements
and unit multipliers. Pressing the [ENTER] key will display the selection for lines a, b, c and d.
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- 1 Introduction 7
- 2 Safety instructions 7
- WARNINGS: 8
- 3 Unit overview 9
- 3.2.1 Menu Structure 10
- 3.2.2 Navigation keys 10
- ↑ in Display 11
- 3.2.6 ”Save changes” dialog 12
- 3.2.7 Security Passwords 12
- 3.3 Display 12
- 4 Installation instruction 13
- 4.1.2 Installation procedure 14
- �40 ... �60 mm 15
- �1.57... �2.36" 15
- 4.2.1 Housing (wall mount) 16
- 4.3 Connector PIN definition 17
- 4.3.1 TB1 and TB2 17
- 4.4.2 AK9 Cable Assignment 20
- A B C D E F S 21
- 4.4.4 VP Cable Assignment 22
- 4.4.5.1 Example 1 23
- 4.4.5.2 Example 2 24
- 4.4.5.3 Example 3 25
- 4.4.5.4 Example 4 26
- A B C D E F 29
- 6 Quick Setup 31
- 7 Sensor Calibration 32
- 7.3 Oxygen Calibration 33
- 7.3.3 Process Calibration 34
- 7.4 pH Calibration 35
- 7.4.1 One point calibration 35
- 7.4.2 Two point calibration 36
- 7.4.3 Process calibration 36
- 7.4.4 mV calibration 36
- 7.7 Sensor Verification 38
- 8 Configuration 39
- 8.2.3 pH / O 40
- Parameter related settings 40
- 8.2.3.2 pH Parameters 41
- 8.2.4 Set Averaging 42
- 8.3 Analog Outputs 43
- 8.4 Setpoints 44
- 8.5 Alarm / Clean 45
- 8.5.1 Alarm 45
- 8.5.2 Clean 46
- 8.6.1 Sensor Monitoring 46
- 8.6.2 CIP Cycle Limit 47
- 8.6.3 SIP Cycle Limit 48
- 8.7 Display 49
- 8.7.1 Measurement 49
- 8.7.2 Resolution 50
- 8.7.3 Backlight 50
- 8.7.4 Name 50
- 8.8 Hold Analog Outputs 51
- 9 System 52
- 9.3 Passwords 53
- 9.3.1 Changing Passwords 53
- 9.4 Set / Clear Lockout 54
- 9.5 Reset 54
- 9.5.1 Reset System 54
- 9.6 Set Date & Time 55
- 10 PID Setup 56
- 10.1 Enter PID Setup 57
- 10.2 PID Auto / Manual 57
- 10.3 Mode 58
- 10.3.1 PID Mode 58
- 10.4 Tune Parameters 59
- 10.4.3 Proportional Limits 60
- 10.4.4 Corner Points 60
- 10.5 PID Display 60
- 11 Service 61
- 11.1.3 Display 62
- 11.1.4 Keypad 62
- 11.1.5 Memory 62
- 11.1.6 Set Relay 62
- 11.1.7 Read Relays 63
- 11.1.8 Set Analog Outputs 63
- 11.1.9 Read Analog Outputs 63
- 11.2 Calibrate 64
- 11.2.1.1 Temperature 64
- 11.2.1.2 Current 65
- 11.2.1.3 Voltage 65
- 11.2.1.4 Rg Diagnostic 66
- 11.2.1.5 Rr Diagnostics 66
- 11.2.2 Calibrate Analog 67
- 11.2.3 Calibrate Unlock 67
- 11.3 Tech Service 67
- 12 Info 68
- 13 Maintenance 71
- 14 Troubleshooting 71
- 14.1 Changing the Fuse 72
- 16 Specifications 75
- 17 Default tables 77
- 17.2 M400 78
- 17.3 Error messages 80
- 18 Warranty 81
- 19 Buffer tables 82
- 19.3 NIST Technical Buffers 83
- 19.5 Hach buffers 84
- 19.6 Ciba (94) buffers 84
- 19.8 WTW buffers 85
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Mettler Toledo M400
(70 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern