Mettler Toledo PS6L Spezifikationen Seite 52
- Seite / 75
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 5 : Service and Repair
5-3 (08/04)
When disconnected from the scale, the voltage on the power supply should be close to
9 VDC. If the voltage on the universal power supply does not read within the range of 8.5
VDC to 9.5 VDC, replace the wall transformer.
Alternate Method: Check to see if scale can be energized by USB connection.
o Disconnect power supply from AC outlet. Disconnect RS232 cable from the
scale.
o Re-connect scale by USB method to PC. Plug small end of USB cable (USB B
connector) to the scale and large end (USB A connector) into a PC. A direct
connection to the PC is required. Do not use an USB hub.
o If scale display is energized with the USB cable connected than the power
supply or power supply connector is bad.
Blank Display
Scale is not receiving power or the display cable is not attached to the scale base
properly.
• For RS232, confirm power supply is plugged into working AC outlet and power
supply is plugged properly into scale base.
• If using USB, make sure USB cable is pushed in all the way at both the scale and the
PC.
• If you have verified that the scale is receiving power, and you still have nothing on
the display, then check the display cable at the connectors. Unplug display by
pushing in on the connector tab and pulling back on the cable. Reinsert the display
cable into the scale connector making sure the tab clicks into position.
If the blank display continues, replace the 0270 Display.
No Keypad Interaction
The UNITS key may be disabled in operation depending on the model or capacity and
increment size selected in the Build parameter in setup. For these models, the UNITS key
will still function in the set up mode. The I/O function for the zero key is disabled on
most models.
To test the operation of the keypad, remove power, then reapply. With power to the unit,
attempt to enter setup mode by pressing and holding the UNITS key (IE: 8-10 sec). If
the display does not indicate setup mode, replace the 0270 Display.
Indicator Locked
To test operation of the indicator, remove power, then reapply. With power to the unit
and display reading zero, add weight. If no change in weight is displayed, replace either
the load cell or the Logic PCB.
The I/O function on the keypad
is disabled in most models.
Cycle the power by unplugging
the scale from its power source.
- Shipping Scales 1
- METTLER TOLEDO 2
- Publication Problem Report 3
- PRECAUTIONS 6
- CONTENTS 8
- 1 Introduction 10
- Standard Features 11
- Optional Accessories 12
- Specifications 13
- Physical Dimensions 13
- Power Requirements 14
- Environmental 14
- Requirements 14
- Standards Compliance 15
- RFI Susceptibility 15
- Chapter 1: Introduction 16
- 1-7 (08/09) 16
- FOR YOUR NOTES 17
- 2 Installation 18
- Correct Level 21
- Incorrect Level 21
- USB Connection - Preferred 22
- Location Codes 24
- Installation of 25
- Accessory Items 25
- Remote Displays 25
- Installing the Ball 28
- Transfer Platter 28
- Installing Conveyor 28
- Drop in Kit for PS90 28
- Power-up Sequence 30
- Keypad and Display 31
- The Display 31
- Keys and Navigation 31
- Operator Functions 32
- Parcel Weighing 32
- Unit Switching 32
- Zeroing the Scale 32
- Cleaning and Regular 33
- Maintenance 33
- TECHNICAL MANUAL 36
- PS Scale Program Menu 37
- Configuring Setup 38
- Parameters 38
- Push Button Zero 39
- Zero Cursor 39
- Units at Power-up 40
- Build Program Block 40
- Alternate Units 41
- Mode Program Block 42
- Filter Program Block 42
- Baud Program Block 42
- Sleep Program Block 44
- GeoCal™ Program 44
- Calibration Weight 44
- Calibration Program 45
- End Program Block 46
- Metrological Seal 47
- Installation 47
- 4-13 (08/09) 48
- 4-14 (08/09) 49
- 5 Service and Repair 50
- Error Code Section 51
- Check Wall 51
- Transformer 51
- Blank Display 52
- No Keypad Interaction 52
- Indicator Locked 52
- Serial Communication 53
- Test with PC 53
- For MT SIC Proto, also click 55
- Update Processor or 56
- Scale Software 56
- CAUTION 56
- Replace Main PCB 57
- Load Cell 58
- Replacement 58
- Replacing the Base 59
- Mount Display 59
- 5-11 (08/04) 60
- Interface 62
- Scale Status Byte 66
- Scale Confidence 66
- Byte Format 66
- Calibrate Using Host 67
- Configure Scale 68
- Parameters Using 68
- Host Interface 68
- PS30 only 69
- FOR YOUR NOTES 71
- References 72
- Hardware 72
- Electrical Connection 72
- Protocol 73
Verwandte Produkte und Handbücher für Küchenwaage Mettler Toledo PS6L
Küchenwaage Mettler Toledo XP2003S Spezifikationen
(126 Seiten)
(126 Seiten)
Küchenwaage Mettler Toledo VIVA Wartungshandbuch
(142 Seiten)
(142 Seiten)
Küchenwaage Mettler Toledo MT Betriebsanweisung
(129 Seiten)
(129 Seiten)
Küchenwaage Mettler Toledo BBK462 Betriebsanleitung
(106 Seiten)
(106 Seiten)
Küchenwaage Mettler Toledo AG Spezifikationen
(76 Seiten)
(76 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.216 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern