Mettler Toledo M400 Spezifikationen Seite 71
- Seite / 131
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Transmitter M400 71
© 02 / 2010 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M400
Printed in Switzerland 52 121 378
8.2.3.3 ISFET parameters
If during the channel setup (see chapter 8.2.1 “Channel setup”) the parameter ISFET has been
chosen, the parameters drift control, buffer recognition, STC, IP, fixed Calibration temperature
and the displayed units for slope and zero point can be set resp. adjusted.
In case, that an ISFET sensor has been parameterized, the menu “ISFET” will be displayed and
has to be chosen. (see chapter 8.2.3 “Parameter related settings”)
In the same way as described for pH parameters (see chapter 8.2.3.2 “pH/ORP parameters”)
parameters for ISFET sensors can be modified.
8.2.3.4 Parameters for oxygen measurement
based on amperometric sensors
If during the channel setup (see chapter 8.2.1 “Channel setup”) the parameter O2 hi or O2 lo
has been chosen or an oxygen sensor based on ISM technology is connected to the transmitter,
the parameters calibration pressure, process pressure, ProCalPres, salinity and relative humidity
can be set resp. adjusted. If an ISM sensor is connected, there is furthermore the option to adjust
the parameterization voltage.
For doing this adjustments resp. settings the menu “O2”, that will be displayed, has to be cho-
sen. (see chapter 8.2.3 “Parameter related settings”)
Enter the Calibration pressure in line 3. The default value for CalPres is 759.8 and the default
unit is mmHg.
To enter the process pressure navigate to line 4. The units for process pressure and calibration
pressure do not have to be the same.
Press [ENTER]
For the algorithm of the process calibration the applied pressure (ProcCalPres) has to be de-
fined. The value of the process pressure (ProcPres) or the calibration pressure (CalPres) can be
used. Chose the pressure, that applies during the process calibration, resp. should be used for
the algorithm and press [ENTER]
In the next step the salinity of the measured solution can be modified.
In addition the relative humidity of the calibration gas can also be entered. The allowed values
for relative humidity are in the range 0% to 100%. When no humidity measurement is avail-
able, use 50% (default value).
Press [ENTER]
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- Transmitter M400 2 2
- Transmitter M400 4 4
- Transmitter M400 5 5
- Transmitter M400 6 6
- Transmitter M400 7 7
- Transmitter M400 8 8
- 1 Introduction 9
- 2 Safety instructions 10
- Transmitter M400 11 11
- 2.3 Ex Classication 12
- 3 Unit overview 13
- 3.2.1 Menu Structure 14
- 3.2.2 Navigation keys 14
- Transmitter M400 15 15
- 3.2.6 ”Save changes” dialog 16
- 3.2.7 Security Passwords 16
- 3.2.8 Display 16
- 4 Installation instruction 17
- 4.1.2 Installation procedure 18
- 40 ... 60 mm 19
- 1.57... 2.36" 19
- 4.2.1 Housing (wall mount) 20
- 4.3 Connector PIN denition 21
- TB1 and TB2 21
- Transmitter M400 22 22
- Transmitter M400 23 23
- Transmitter M400 24 24
- Transmitter M400 25 25
- Transmitter M400 26 26
- A B C D E F 27
- A B C D E F S 28
- 4.5.3.1 Example 1 30
- 4.5.3.2 Example 2 31
- 4.5.3.3 Example 3 32
- 4.5.3.4 Example 4 33
- Transmitter M400 34 34
- 1 2 3 4 5 35
- 9 8 7 6 35
- Transmitter M400 37 37
- Transmitter M400 40 40
- 6 Quick Setup 41
- 7 Sensor Calibration 42
- Transmitter M400 43 43
- (four electrode sensors only) 44
- 7.2.3 Process Calibration 45
- Transmitter M400 46 46
- Transmitter M400 47 47
- 7.3.3 Process calibration 48
- Transmitter M400 49 49
- Transmitter M400 50 50
- 7.5.1.1 Auto mode 51
- 7.5.1.2 Manual mode 51
- 7.5.2.1 Auto mode 52
- 7.5.2.2 Manual mode 52
- 7.5.3 Process calibration 53
- 7.6 pH calibration 54
- 7.6.1 One point calibration 54
- 7.6.1.1 Auto mode 54
- 7.6.2 Two-point calibration 55
- 7.6.1.2 Manual Mode 55
- 7.6.2.1 Auto Mode 56
- 7.6.2.2 Manual Mode 56
- 7.6.3 Process calibration 57
- Transmitter M400 58 58
- 7.7 ISFET calibration 59
- 7.7.1 One-point calibration 59
- 7.7.2 Two-point calibration 59
- 7.7.3 Process calibration 59
- 7.7.4 mV calibration 60
- 7.8.1 One point calibration 60
- 7.8.1.1 Auto Mode 60
- 7.8.1.2 Manual Mode 61
- 7.8.2 Two-point calibration 61
- 7.8.2.1 Auto Mode 62
- 7.8.2.2 Manual Mode 62
- 7.8.3 Process calibration 63
- (only for analog sensors) 63
- Transmitter M400 64 64
- (only for analog sensor) 65
- 7.11 Sensor verication 65
- 8 Conguration 66
- 8.2.1.1 Analog sensor 67
- 8.2.1.2 ISM sensor 67
- or . key. Press [ENTER] 68
- Transmitter M400 69 69
- 8.2.3.2 pH/ORP parameters 70
- 8.2.3.3 ISFET parameters 71
- Transmitter M400 72 72
- 8.2.3.7 LED Mode 73
- Transmitter M400 74 74
- 8.2.4 Set averaging 75
- 8.3 Analog outputs 76
- 8.4 Set points 77
- 8.5 Alarm / Clean 78
- 8.5.1 Alarm 78
- Transmitter M400 79 79
- 8.5.2 Clean 80
- 8.6 ISM set up 80
- 8.6.1 Sensor monitoring 80
- Transmitter M400 81 81
- 8.6.2 CIP Cycle Limit 82
- 8.6.3 SIP Cycle Limit 83
- and . keys and press 84
- 8.7 Display 85
- 8.7.1 Measurement 85
- 8.7.2 Resolution 85
- 8.7.3 Backlight 86
- 8.7.4 Name 86
- 8.8 Hold analog outputs 87
- 9 System 88
- 9.3 Passwords 89
- 9.3.1 Changing passwords 89
- 9.4 Set / Clear lockout 90
- 9.5 Reset 90
- 9.5.1 Reset system 90
- 9.6 Set date & time 91
- 10 PID setup 92
- 10.1 Enter PID setup 93
- 10.2 PID auto / manual 93
- 10.3 Mode 94
- 10.3.1 PID mode 94
- 10.4 Tune parameters 95
- 10.4.3 Proportional limits 96
- 10.4.4 Corner points 96
- 10.5 PID display 96
- 11 Service 97
- 11.1.2 Digital input 98
- 11.1.3 Display 98
- 11.1.4 Keypad 98
- 11.1.5 Memory 98
- 11.1.6 Set Relay 99
- 11.1.7 Read relays 99
- 11.1.8 Set analog outputs 99
- 11.1.9 Read analog outputs 99
- 11.1.10 0 100
- Optical 100
- 11.2 Calibrate 100
- 11.2.1.1 Temperature 100
- 11.2.1.2 Current 101
- 11.2.1.3 Voltage 102
- 11.2.1.4 Rg diagnostic 102
- 11.2.1.5 Rr diagnostics 103
- 11.2.1.6 Calibrate analog 103
- 11.2.2 Calibrate unlock 104
- 11.3 Tech Service 104
- 12 Info 105
- 12.4 ISM sensor info 106
- Transmitter M400 107 107
- Transmitter M400 108 108
- 13 Maintenance 109
- 14 Troubleshooting 110
- Transmitter M400 111 111
- Transmitter M400 112 112
- Warning O 113
- Alarms Description 113
- 14.7 Optical O 113
- Warning- and Alarm list 114
- 14.10.1 115
- 14.10.2 Alarm indication 115
- Transmitter M400 116 116
- 16 Specications 117
- Transmitter M400 118 118
- Transmitter M400 119 119
- Transmitter M400 120 120
- Transmitter M400 121 121
- 16.5 Ex Classication 122
- 17 Default table 123
- Transmitter M400 124 124
- Transmitter M400 125 125
- 18 Warranty 126
- 19 Buffer tables 127
- 19.3 NIST Technical Buffers 128
- 19.5 Hach buffers 129
- 19.6 Ciba (94) buffers 129
- 19.8 WTW buffers 130
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Mettler Toledo M400
(88 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern