Mettler Toledo M400/2(X)H Spezifikationen Seite 19
- Seite / 111
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Transmitter M400/2(X)H, M400G/2XH 19
© 03 / 2014 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M400/2(X)H, M400G/2XH
Printed in Switzerland 30 031 683
4.1.2 Installation procedure
General:
– Orient the transmitter so that the cable grips face downward.
– Wiring routed through the cable grips shall be suitable for use in wet locations.
– In order provide IP66 enclosure ratings, all cable glands must be in place. Each cable gland
must be filled using a cable, or suitable Cable Gland Hole Seal.
For Wall Mount:
– Remove rear cover from front housing.
– Start by unscrewing the four screws located on the face of the transmitter, in each corner. This
allows the front cover to swing away from the rear housing.
– Remove the hinge-pin by squeezing the pin from each end. This allows the front housing to
be removed from the rear housing
– Mount rear housing to wall. Secure mounting kit to the M400 according to the supplied
instructions. Attach to wall using appropriate mounting hardware for wall surface. Be sure it
is level and securely fastened and the installation adheres to any and all clearance dimen-
sions required for transmitter service and maintenance. Orient the transmitter so that the
cable grips are facing downward.
– Replace the front housing to the rear housing. Securely tighten the rear-cover screws to
ensure that IP66/NEMA4X enclosure environmental rating is maintained. The unit is ready to
be wired.
For Pipe Mount:
– Use only manufacturer-supplied components for pipe-mounting the M400 transmitter and
install per the supplied instructions. See section 15 for ordering information.
4.1.3 Assembly – 1/2DIN version
1
2
3
1. 3 M20X1.5 cable glands
2. Plastics plugs
3. 4 screws
- Operation Manual 1
- Multi-parameter 1
- 1 Introduction 9
- 2 Safety instructions 10
- 3 Unit overview 14
- 3.2.1 Menu Structure 15
- 3.2.2 Navigation keys 15
- 3.2.6 ”Save changes” dialog 17
- 3.2.7 Security Passwords 17
- 3.2.8 Display 17
- 4 Installation instruction 18
- 4.1.2 Installation procedure 19
- (+ 0,5 mm/– 0,0 mm) 20
- (+ 0.02"/– 0.00") 20
- 4.2.1 Housing (wall mount) 21
- 4.3 Connector PIN denition 22
- 4.3.3 Analog Sensors 23
- InPro 3250i/SG/120 25
- Art.-Nr. 52 005 373 25
- 4.5.2.1 Example 1 27
- 4.5.2.2 Example 2 28
- 4.5.2.3 Example 3 29
- 4.5.2.4 Example 4 30
- 6 Quick Setup 34
- 7 Sensor Calibration 35
- (four electrode sensors only) 37
- 7.2.3 Process Calibration 38
- 7.3.1.1 Auto mode 39
- 7.3.1.2 Manual mode 40
- 7.4 pH calibration 41
- 7.4.1 One point calibration 41
- 7.4.1.1 Auto mode 41
- 7.4.1.2 Manual Mode 42
- 7.4.2 Two-point calibration 42
- 7.4.2.1 Auto Mode 42
- 7.4.2.2 Manual Mode 43
- 7.4.3 Process calibration 44
- (only for analog sensors) 46
- (only for analog sensor) 47
- 7.7 Sensor verication 47
- 8 Conguration 48
- 8.2.1.1 Analog sensor 49
- 8.2.1.2 ISM sensor 49
- 8.2.3.2 Concentration table 52
- 8.2.3.3 pH / ORP parameters 53
- or . key 54
- 8.2.4 Set averaging 55
- 8.3 Analog outputs 56
- 8.4 Set points 57
- 8.5 Alarm / Clean 58
- 8.5.1 Alarm 58
- 8.5.2 Clean 59
- 8.6 ISM set up 60
- 8.6.1 Sensor monitoring 60
- 8.6.2 CIP Cycle Limit 61
- 8.6.3 SIP Cycle Limit 62
- and . keys and press 63
- 8.7 Display 64
- 8.7.1 Measurement 64
- 8.7.2 Resolution 65
- 8.7.3 Backlight 65
- 8.7.4 Name 65
- 8.8 Hold analog outputs 66
- 9 System 67
- 9.2.1 Changing passwords 68
- 9.3 Set / Clear lockout 68
- 9.4 Reset 68
- 9.4.1 Reset system 69
- 9.5 Set date & time 69
- 10 PID setup 70
- 10.1 Enter PID setup 71
- 10.2 PID auto / manual 71
- 10.3 Mode 71
- 10.3.1 PID mode 72
- 10.4 Tune parameters 73
- 10.4.3 Proportional limits 73
- 10.4.4 Corner points 73
- 10.5 PID display 74
- 11 Service 75
- 11.1.3 Display 76
- 11.1.4 Keypad 76
- 11.1.5 Memory 76
- 11.1.6 Set OC 76
- 11.1.7 Read OC 77
- 11.1.8 Set analog outputs 77
- 11.1.9 Read analog outputs 77
- 11.2 Calibrate 77
- 11.2.1.1 Temperature 78
- 11.2.1.2 Current 78
- 11.2.1.3 Voltage 79
- 11.2.1.4 Rg diagnostic 79
- 11.2.1.5 Rr diagnostic 80
- 11.2.2 Calibrate unlock 81
- 11.3 Tech Service 81
- 12 Info 82
- 12.4 ISM sensor info 83
- 13 Maintenance 86
- 14 Troubleshooting 87
- 14.3.3 ORP messages 89
- 14.4 Amperometric O 90
- Error messages / 90
- Warning- and Alarm list 90
- 14.4.3 Trace oxygen sensors 91
- 14.5.1 Warning indication 92
- 14.5.2 Alarm indication 92
- 16 Specications 94
- 17 Default table 99
- Resistivity/Conductivity 103
- 18 Warranty 104
- 19 Buffer tables 105
- 19.1.2 Mettler-10 106
- 19.1.5 Hach buffers 107
- 19.1.6 Ciba (94) buffers 108
- 19.1.8 WTW buffers 109
- 19.1.9 JIS Z 8802 buffers 109
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Mettler Toledo M400/2(X)H
(131 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern