Mettler Toledo M400/2(X)H Spezifikationen Seite 43
- Seite / 111
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Transmitter M400/2(X)H, M400G/2XH 43
© 03 / 2014 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M400/2(X)H, M400G/2XH
Printed in Switzerland 30 031 683
The display shows the buffer the transmitter has recognized (Point 1) and the measured value.
As soon as the stabilisation criteria have been fulfilled stabilisation criteria have been fulfilled,
the display changes and prompts you to place the electrode in the second buffer.
Place the electrode in the second buffer solution and press the [ENTER] key to go on with the
calibration.
The display shows the second buffer the transmitter has recognized (Point 2) and the measured
value.
As soon as the stabilisation criteria have been fulfilled the display changes to show the slope
calibration factor S and the offset calibration factor Z.
In case of a successful calibration, the calibration values are stored in the cal history* and taken
over (Adjust), stored in the cal history* and not taken over (Calibrate) or discarded (Abort).
* only available with ISM sensor. The values will be stored in the sensor.
If “Adjust” or “Calibrate” are chosen, the message “Calibration successful” is displayed. In any
case you will get the message “Re-install sensor” and “Press ENTER” on the display. After press-
ing “ENTER” the M400 returns to the measuring mode.
7.4.2.2 Manual Mode
Place the electrode in the first buffer solution. The display shows the buffer the transmitter has
recognized (Point 1) and the measured value. Press [ENTER] to proceed.
Place the transmitter in the second buffer solution. The display shows the buffer the transmitter
has recognized (Point 2) and the measured value. Press [ENTER] to proceed.
The display shows the slope calibration factor S and the offset calibration factor Z.
In case of a successful calibration, the calibration values are stored in the cal history* and taken
over (Adjust), stored in the cal history* and not taken over (Calibrate) or discarded (Abort).
If “Adjust” or “Calibrate” are chosen, the message “Calibration successful” is displayed. In any
case you will get the message “Re-install sensor” and “Press ENTER” on the display. After press-
ing “ENTER” the M400 returns to the measuring mode.
- Operation Manual 1
- Multi-parameter 1
- 1 Introduction 9
- 2 Safety instructions 10
- 3 Unit overview 14
- 3.2.1 Menu Structure 15
- 3.2.2 Navigation keys 15
- 3.2.6 ”Save changes” dialog 17
- 3.2.7 Security Passwords 17
- 3.2.8 Display 17
- 4 Installation instruction 18
- 4.1.2 Installation procedure 19
- (+ 0,5 mm/– 0,0 mm) 20
- (+ 0.02"/– 0.00") 20
- 4.2.1 Housing (wall mount) 21
- 4.3 Connector PIN denition 22
- 4.3.3 Analog Sensors 23
- InPro 3250i/SG/120 25
- Art.-Nr. 52 005 373 25
- 4.5.2.1 Example 1 27
- 4.5.2.2 Example 2 28
- 4.5.2.3 Example 3 29
- 4.5.2.4 Example 4 30
- 6 Quick Setup 34
- 7 Sensor Calibration 35
- (four electrode sensors only) 37
- 7.2.3 Process Calibration 38
- 7.3.1.1 Auto mode 39
- 7.3.1.2 Manual mode 40
- 7.4 pH calibration 41
- 7.4.1 One point calibration 41
- 7.4.1.1 Auto mode 41
- 7.4.1.2 Manual Mode 42
- 7.4.2 Two-point calibration 42
- 7.4.2.1 Auto Mode 42
- 7.4.2.2 Manual Mode 43
- 7.4.3 Process calibration 44
- (only for analog sensors) 46
- (only for analog sensor) 47
- 7.7 Sensor verication 47
- 8 Conguration 48
- 8.2.1.1 Analog sensor 49
- 8.2.1.2 ISM sensor 49
- 8.2.3.2 Concentration table 52
- 8.2.3.3 pH / ORP parameters 53
- or . key 54
- 8.2.4 Set averaging 55
- 8.3 Analog outputs 56
- 8.4 Set points 57
- 8.5 Alarm / Clean 58
- 8.5.1 Alarm 58
- 8.5.2 Clean 59
- 8.6 ISM set up 60
- 8.6.1 Sensor monitoring 60
- 8.6.2 CIP Cycle Limit 61
- 8.6.3 SIP Cycle Limit 62
- and . keys and press 63
- 8.7 Display 64
- 8.7.1 Measurement 64
- 8.7.2 Resolution 65
- 8.7.3 Backlight 65
- 8.7.4 Name 65
- 8.8 Hold analog outputs 66
- 9 System 67
- 9.2.1 Changing passwords 68
- 9.3 Set / Clear lockout 68
- 9.4 Reset 68
- 9.4.1 Reset system 69
- 9.5 Set date & time 69
- 10 PID setup 70
- 10.1 Enter PID setup 71
- 10.2 PID auto / manual 71
- 10.3 Mode 71
- 10.3.1 PID mode 72
- 10.4 Tune parameters 73
- 10.4.3 Proportional limits 73
- 10.4.4 Corner points 73
- 10.5 PID display 74
- 11 Service 75
- 11.1.3 Display 76
- 11.1.4 Keypad 76
- 11.1.5 Memory 76
- 11.1.6 Set OC 76
- 11.1.7 Read OC 77
- 11.1.8 Set analog outputs 77
- 11.1.9 Read analog outputs 77
- 11.2 Calibrate 77
- 11.2.1.1 Temperature 78
- 11.2.1.2 Current 78
- 11.2.1.3 Voltage 79
- 11.2.1.4 Rg diagnostic 79
- 11.2.1.5 Rr diagnostic 80
- 11.2.2 Calibrate unlock 81
- 11.3 Tech Service 81
- 12 Info 82
- 12.4 ISM sensor info 83
- 13 Maintenance 86
- 14 Troubleshooting 87
- 14.3.3 ORP messages 89
- 14.4 Amperometric O 90
- Error messages / 90
- Warning- and Alarm list 90
- 14.4.3 Trace oxygen sensors 91
- 14.5.1 Warning indication 92
- 14.5.2 Alarm indication 92
- 16 Specications 94
- 17 Default table 99
- Resistivity/Conductivity 103
- 18 Warranty 104
- 19 Buffer tables 105
- 19.1.2 Mettler-10 106
- 19.1.5 Hach buffers 107
- 19.1.6 Ciba (94) buffers 108
- 19.1.8 WTW buffers 109
- 19.1.9 JIS Z 8802 buffers 109
Verwandte Produkte und Handbücher für Messen, Testen & Steuern Mettler Toledo M400/2(X)H
(131 Seiten)
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern